mathews no cam draw length adjustment

fontecchio April 09, 2022 draw , length , mathews , no Comment

An in depth Mathews HTR No Cam review including details on one of the most accurate cam systems ever seen on a compound bow. The lower the let-off the faster the bow.

Cam Adjustment Mission Archery By Mathews

This is compared to my dual cam Monster Chill with the same arrow and draw.

. V3X 29. Brace Height6 58 inches. Take it to a Mathews dealer and theyll order you the correct mods.

Adjust peak draw weight and draw length with the quick change of a module. 41443 pounds approximate Axle-To-Axle Length. Mathews module for Mathews model bows for modular draw length adjustment.

Draw lengths can be changed in under 30 seconds with the simple use of an allen wrench. Draw Length If your new Mathews SoloCam bow is equipped with a StraightLine MaxCam which is draw length specific there is no adjustment on the cam. Modules are labeled A through J See charts for appropriate draw length selection.

See image for module chart. Modules to suit the Mathews HTR and TRG No-Cam bows. Letoff 65 75 85 optional.

Each mod is programmed to deliver maximum efficiency resulting in an ultra-smooth draw without sacrificing speed. The NO CAM system delivers a new level of smooth all while transferring the most amount of energy into the arrow possible. Remove the setscrews in the cams with a screwdriver.

Draw weight adjustments are made using either a 316 or 732 Allen Wrench. The TRG 7 with NO CAM ST technology equates to one of the most accurate stable and balanced bows ever. This bow had a draw length that was to long for me.

Your shooting style should be measured to ensure a proper fit. Them that dont know him wont like him and them that do sometimes wont know how to take him. Compatible bows are the.

With the exception of the Mathews Mission series Mathews bows are designed draw length specific and do not provide for setting adjustment. He aint wrong hes just different and his pride wont let him do things to make you think hes right. Its available in peak draw weights of 50 60 or 70 pounds and has an adjustable system letoff of 65 75 or 85 percent.

As noted earlier these modules can change both your draw length as well as your let-off which will change your bows speed. Adjusting the draw length on your Mission bow has never been easier than with new FastFit Cam Technology. Turn the limb bolt clockwise to increase the draw weight or counterclockwise to decrease the draw weight.

The lower the let-off the faster the bow. Mathews Chill Draw Length Question Archery Talk Forum Most Mathews bows are engineered to be draw length specific and offer no draw length adjustment on the cam. The NO CAM HTR weighs 43 pounds has a 6 58-inch brace height and can accommodate draw lengths from 24-30 inches in half-inch increments.

How do you change the draw length on a Mathews no Cam. In this video we will go over the new Mathews bow that I got awhile back. Mathews Vertix Draw Length Adjustment.

One rotation of the bolt increases or decreases the draw weight by about two to four pounds. Loosen slide and retighten. Insert the Allen wrench into one of the limb bolts on the bow.

Mathews NO CAM TRG 7 Description. So I went to my local archery. For reference my HTR is setup with 85 let-off modules and a 285 draw length at 70 lbs and it is shooting a 450 grain arrow at 269 fps.

Mathews Vertix Draw Length Adjustment. The limb bolt should be snug. Its only a couple Allen screws to take out.

Simply remove the two allen screws that hold the module to the wheel and install your new module in its place. I think that a Matthews dealer can order a new cam for you and change the draw length. Mathews bows with SwitchWeight technology allows for adjustment of Draw Length Draw Weight and Let-Off all with the swapping of a cam module.

VXR 28 315 Weights. While the Mission series draw length can be changed with a setscrew on the cams you will need to replace the cams to change the draw length on other models of Mathews bows. FastFit Cam technology is utilized on the Hammr Radik and Switch.

Was shooting at my coachs last night and he and another shooter there both Mathews sponsored shooters said that theyve noticed on the Z7 and the Triumph that the draw length was longer than usual. Simply remove the two allen screws that hold the module to the wheel and install your new module in its place. High-efficiency CAM system that delivers accurate energy with an incredibly smooth draw.

Same size cam as on all my other Mathews bows but this sucker is proving harder to tune. How do you change the draw length on a Mathews no cam. The bows IBO speed ratings are 330 fps at 65 percent letoff 325 fps at 75 percent.

Or if you know what draw length you are you can try and find a set on archery talk. 24 to 30 inches in half-inch increments. Shouldnt be more than 30.

The rating of this product is. Repeat steps one and two on the other limb bolt. Other Mathews cams are adjustable for.

We take the new Mathews No Cam HTR for a test run. The NO CAM technology utilises two circular wheels allowing the nock to remain level. Sent from my iPhone using Tapatalk.

Most Mathews bows are engineered to be draw length specific and offer no draw length adjustment on the cam. As noted earlier these modules can change both your draw length as well as your let-off which will change your bows speed. Mathews No Cam HTR Specs.

Draw length can be changed by changing the mods. Both limb bolts must be adjusted equally or the bow may become out of tunesynchronization. See below for an instructional video and an adjustment chart to.

If my draw length is off by a hair it drives me nuts. Turn the limb bolt clockwise to increase the draw weight and counter clockwise to decrease the weight.

Bow Report Mathews No Cam Htr Grand View Outdoors